Friginox

MX 10-5 A CT GN 1/1
Fluid R452A
– Dim (mm): 650 x 485 x 700
– Power Elec: 830W – Mono 230V + T
– Capacity: Refr. : 10 kG, Frieza. Load: 5 kG
– Keeping warm: 70 ° C – Air unit housed
– Loading format: GN 1/1
– External coating in 18-10 stainless steel or steel
– white lacquered
– Internal coating in 18-10 stainless steel
– Use mixed:
– Rapid cooling 10 kg from +64.5 ° C to + 8.5 ° C at
– core per cycle of 2 hours maximum
– Rapid freezing 5 kg from +64.5 ° C to -19.5 ° C at heart by
– cycle of 4 h 50 min maximum
– Keeping warm at + 70 ° C
– Switching from -20 ° C to 70 ° C in 30 minutes (vacuum appliance).
– Standard 1 point probe
– 3 pairs of fixed guides, removable at intervals of 65
– mm
– Door with left-hand hardware with
door opening stop
– Front frame with anti
– condensation device – 20 mm feet, adjustable in height
– Insulation by injected polyurethane foam, without CFCs,
– HCFC or HFC
– Air-cooled refrigeration unit, with exhaust
– of the air at the rear and on the right side
– Automatic re-evaporation of defrost water
– Hermetic
refrigeration compressor
– R452A refrigerant – Anti-corrosion treated refrigeration evaporator with
– thermostatic expansion valve
– Heating by waterproof electric resistance in steel
– stainless
– Hot safety thermostat
MX 20-10 A EC RAPID BLAST CHILLER
 
Fluid R452A
– Dim (mm): 770 x 820 x 945
– Elec power: 1600W – Mono 230V
– Capacity: Refr. : 20 kG, Frieza. Load: 10 kG
– Air unit housed
– Mixed use:
– Rapid cooling +64.5 ° C to +8.5 ° C through core per cycle of 2 hours maximum
– Rapid freezing +64.5 ° C to -19.5 ° C to core per cycle of 4 h 50 min max

Standard 1 point penetrating probe – Height-adjustable “U” type slides for GN 1/1 shelves and trays (not supplied)
– Stainless steel exterior and interior coating
– Framing of facade with an anti-condensation device
– Internal rounded
corners – Magnetic door seal removable without tools
– 60 mm thick injected polyurethane insulation
– Sloping drain and cell bottom for water evacuation
– Floor without threshold
– Standard stainless steel feet
– Interior fittings removable without tools
– Evaporator with anti-corrosion treatment
– Motorcycle – Evaporator fan (s) with stainless steel grid as standard
– Defrost by forced operation of the fan (door open)
– Stop ventilation when the door is opened
– Insulation and refrigerant without CFC, HCFC or HFC
– Control panel waterproof

Mobile Holding Cabinet

Rolfast series 

MULTI-FUNCTION MOBILE CABINET
HOT – COLD – ISOTHERMAL TRANSPORT
INTERNAL VOLUME: 170 LITRES
FOR GN 1/1 TRAYS
INSIDE TEMPERATURE: +1 °C to +80 °C
HOT ISOTHERMAL CAPACITY OF 7 HOURS
COLD ISOTHERMAL CAPACITY OF 8 HOURS
AMBIENT TEMPERATURE 43 °C
100% 304 STAINLESS STEEL
STAINLESS STEEL NON MARKING CASTERS
KEY LOCKING
ELECTRONIC CONTROL
0 % CFC AND HCFC
  • External finish made of 304 stainless steel.
  • Inside walls with press-drawn runners (55 mm apart).
  • Drain hole in lower part.
  • Access by door, folding back on the side (270°), with fastening
  • Chrome steel latch lock, with key locking.
  • 4 casters, diameter 125 mm made of 304 stainless steel with
  • 4 ergonomic side handles for moving.
  • Peripheral non-marking shockproof protection.
  • Water recovery drainer under the door.
  • Injectedpolyurethanefoaminsulation,60to80mmthick,without
  • Format: Gastronorm GN 1/1, 325 mm wide.
  • Capacities:
  • H55 mm = 15,
  • H65 mm = 8,
  • H100 mm = 7,
  • H150 mm = 5.
  • Possibility of loading formats GN 1/3, GN 2/3 and GN 1/2.
  • Inside temperature: +1°C to +80°C.
  • Hot isothermal capacity of 7 hours, cold: 8 hours. With solid door.
  • Reaching of required temperature when empty:
  • – Hot: 10 minutes,
  • – Cold: 50 minutes.